Motors, Drivers, Actuators
Motors, Drivers, Actuators
Mounting Bracket for N20 Micro Gear Motors - (White)
N20 Gear Motor Bracket White is a lightweight bracket for an N20 gear motor. This is compact bracket enables convenient mounting of popular N20 Gear Motor.
Features:
Color: White
Material: High-Quality Plastic
Rs. 65.00
Rs. 19.00
Dead Axle, Free Axle, Dummy Motor 6mm Shaft
Free Axle Set of 4 CS Motor Top Part Shaft Size: 6mm; Length: 23mm Used for idle wheel mounting in robot car vehicle--Dead Axle , Free Axle, Dummy Motor 6mm Shaft This free axle module comes in handy when you...
Rs. 60.00
Rs. 39.00
60 RPM CS DC GEAR MOTOR - CENTER SHAFT
The metal gears have better wear and tear properties. The gearbox is sealed and lubricated with lithium grease and requires no maintenance. Although motor gives 60 RPM at 12V, the motor runs smoothly from 4V to 12V and gives a wide...
Rs. 220.00
Rs. 189.00
Rs. 550.00
Rs. 349.00
PCA9685 16-Channel 12-bit PWM / Servo Driver I2C interface for Arduino Raspberry Pi
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all...
Rs. 550.00
Rs. 349.00
200 RPM DUAL SHAFT DC BO MOTOR ( Yellow )
The 200 RPM Dual Shaft BO Motor - Straight motor gives good torque and rpm at lower operating voltages, which is the biggest advantage of these motors. Small shaft with matching wheels gives an optimized design for your application or...
Rs. 150.00
Rs. 59.00
200 RPM CS DC GEAR MOTOR -CENTER SHAFT
Operating Voltage(V): 12
Rated Speed (RPM): 200
Rated Torque(kg-cm): 1.5
Stall Torque(kg-cm): 5.4
Load Current (A): 0.3
No Load Current (A): 0.06
Rs. 230.00
Rs. 149.00
L293D Motor Driver Module Board
L293D motor driver IC. Voltage Range: 4.5 V to 36 V Separate Input-Logic Supply Pin compatible with L293D Internal ESD Protection Male burg stick connectors for supply, ground and input connection Screw terminal connectors for easy motor connection On Board...
Rs. 199.00
Rs. 85.00
150 RPM CS DC GEAR MOTOR -CENTER SHAFT
The metal gears have better wear and tear properties. The gearbox is sealed and lubricated with lithium grease and requires no maintenance. Although the motor gives 150 RPM at 12V, the motor runs smoothly from 4V to 12V and gives a...
Rs. 230.00
Rs. 169.00
12V DC Cabinet Door Drawer Electric Lock Assembly Solenoid Lock (54x42x28)
12 V DC Cabinet Lock Actuator lock Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 54 x 42 x 28 mm (LxWxH) High quality ultra-compact electric lock. This DC 12V Cabinet Door Lock Electric Lock Assembly Solenoid...
Rs. 550.00
Rs. 399.00
ULN2003 Stepper Motor Driver Board
ULN2003A motor driver chip Chip all the pins already leads for easy connection to use 5-12V power supply 4-way signal indicator XH-5P socket can be connected directly 28BYJ-48 Model stepper motor This is the ULN2003 Driver Module Stepper Motor Driver...
Rs. 150.00
Rs. 75.00
200 RPM Johnson DC Gear Motor Side Shaft (New Model)
Johnson Geared Motor Premium Quality Imported New Model 200 RPM Specifications: Rated Base Motor RPM: 18000 Gear Material: Metal Rated Speed (RPM): 200 Operating Voltage (VDC): 6 ~ 18 Nominal Voltage (V): 12 Rated Torque(kg-cm): 3.9 Stall Torque(Kg-Cm): 15.6 No-Load...
Rs. 450.00
Rs. 385.00
Vigor 60 RPM DC BO Gear Motor Single Shaft
Brand VIGOR Type BO Motor Straight Operating Voltage(VDC) 5~12 V No Load Current 40-180mA. Material Plastic Shaft Diameter 5.2mm Shaft Length 8mm Rated Speed(After Reduction) 150 RPM Motor Length ...
Rs. 100.00
Rs. 65.00
600 RPM 6V N20 DC Micro Metal Gear box Motor
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel...
Rs. 450.00
Rs. 275.00
28BYJ-48 DC 5V DC Stepper Motor
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm Note: The system is recommended to run on Half-step mode(8 step control signal sequence) for excellent performance...
Rs. 300.00
Rs. 149.00
Tower Pro MG996R (180) Semi Metal Gear Servo Motor 180 Degree Rotation
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Plastic + Metal gear Dead band width: 1us Wire length: 32cm Servo Plug: JR (Fits JR and...
Rs. 450.00
Rs. 269.00
A4988 Stepper Motor Driver Module
Supply Voltage : 8-35 VDC. Current : 1.0A (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode. The A4988 driver Stepper...
Rs. 250.00
Rs. 99.00
300 RPM CS DC GEAR MOTOR -CENETR SHAFT
Speed: 300 RPM
Operating Voltage: 12 V
Rated Torque: 1.2 Kg-cm
Stall Torque: 3.5 Kg-cm
Load Current: 0.3 A
Rs. 230.00
Rs. 179.00
Vigor 60 RPM DC BO Gear Motor Dual Shaft
Make: Vigor Shaft: Dual Shaft – Straight Shape Operating Voltage : 3V – 12V Rated Speed 60 RPM @9v Material Plastic Gear Housing Shaft Diameter 5.2 mm Shaft Length 8 mm Motor Body Length 70...
Rs. 100.00
Rs. 69.00
500 RPM Johnson DC Gear Motor -Side Shaft
Base Motor RPM: 18000
Operating Voltage: 6-18 V
Rated Voltage: 12 V
Rated Torque: 1 kg-cm
Stall Torque: 4.4 kg-cm
Gearbox Dimensions: 22×37 (LxW) mm
Rs. 450.00
Rs. 379.00
10 RPM Johnson DC Gear Motor -Side Shaft
Base Motor RPM: 18000
Operating Voltage: 6-18 V
Rated Voltage: 12 V
Rated Torque: 11.7 kg-cm
Stall Torque: 46 kg-cm
Gearbox Dimensions: 30×37 (LxW),m
Rs. 480.00
Rs. 415.00
Tower Pro MG996R Metal Gear Servo Motor (360 Degree Rotation)
Metallic gears, standard size, high torque Suitable for arduino, raspberry pi and node mcu. Original tower pro 996r. Stall torque: 9.4 kg‚·cm (4.8 v ), 11 kg,·cm (6 v) Operating speed: 0.17 s/60 (4.8 v), 0.14 s/60(6 v) This is...
Rs. 450.00
Rs. 299.00
6mm Axle Shaft- 203mm / 8 inch
The shaft itself rotates with the wheel, being either bolted or splinted in fixed relation to it, and is called an "axle” or “axle shaft". Features of 6mm Shaft Axle: Length of the Shaft Axle : 203 mm. Diameter of...
Rs. 80.00
Rs. 59.00
500 RPM CS DC GEAR MOTOR -CENTER SHAFT
Operating Voltage(V): 12
Rated Speed (RPM): 500
Rated Torque(kg-cm): 0.7
Stall Torque(kg-cm): 3
No Load Current (A): 0.06
Load Current (A): 0.3
Rs. 220.00
Rs. 149.00
60 RPM Johnson DC Gear Motor -Side Shaft
Base Motor RPM: 18000
Operating Voltage: 6-18 V
Rated Voltage: 12 V
Rated Torque: 7.5 kg-cm
Stall Torque: 30 kg-cm
Gearbox Dimensions: 25×37 (LxW) mm
Rs. 450.00
Rs. 379.00
Showing 25 - 48 of 282 total