SG90 - Micro Servo Motor
Rs. 200.00 Rs. 149.00
SG90 - Micro Servo Motor
SG90 is high torque motor which is commonly used in robotics and several other applications due to the fact that it's easy to control their rotation. Servo motors have a geared output shaft which can be electrically controlled. This can...
Rs. 200.00 Rs. 149.00
Add to wishlist
Digital Multi Servo Tester ESC CCPM Consistency Master Speed Control
The Digital Multi Servo Tester ESC RC Consistency CCPM Master Speed Control offers 3 modes to check servos or ESC. The Manual Mode allows you to turn the knob to different speeds and check the reaction time. The Neutral mode...
Rs. 199.00 Rs. 149.00
Add to wishlist
MG90 - Micro Servo Motor
Rs. 410.00 Rs. 289.00
MG90 - Micro Servo Motor
Working Torque: 2kg/Cm Reaction Speed: 0.11 Seconds / 60 Degrees (4.8v) Servo: Digital Servo Operating Voltage: 4.8v- 6v Structural Material: Metal gear Coreless Motor DUAL BALL Axle Bearing Fit for ALL kind of R/C Toys Operating speed: 0. 1sec/60degree(4. 8v),...
Rs. 410.00 Rs. 289.00
Add to wishlist
MG995 Tower Pro Metal Gear Servo Motor (180 Degree Rotation)
MG995 Standard Mini Micro Servo Gear Compliant with most standard receiver connector: Futaba, Hitec, Sanwa, GWS. Stable and Shock Proof Connector Wire Length 300mm Power Supply: Through External Adapter--Operating Speed: . 0.17sec or 60 degrees (4.8V no load) . 0.13sec...
Rs. 399.00 Rs. 320.00
Add to wishlist
TB6600 Stepper Motor Driver Controller
Input Current: 0~5A Output Current: 0.5~4.0A Control Signal: 3.3~24V Power (MAX): 160W Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32 Temperature: -10~45℃ H bridge bipolar constant current drive.--TB6600 Arduino Stepper Motor Driver is an easy-to-use professional stepper motor driver,...
Rs. 880.00 Rs. 749.00
Add to wishlist
28BYJ-48 Stepper Motor DC 12V
Rs. 300.00 Rs. 149.00
28BYJ-48 Stepper Motor DC 12V
28BYJ-48 -12V DC Stepper Motor This 12V DC 28BYJ-48 Stepper Motor is a small, inexpensive, and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper...
Rs. 300.00 Rs. 149.00
Add to wishlist
Tower Pro MG996R Metal Gear Servo Motor (360 Degree Rotation)
Metallic gears, standard size, high torque Suitable for arduino, raspberry pi and node mcu. Original tower pro 996r. Stall torque: 9.4 kg‚·cm (4.8 v ), 11 kg,·cm (6 v) Operating speed: 0.17 s/60 (4.8 v), 0.14 s/60(6 v)--This is the...
Rs. 320.00
Add to wishlist
2 Axis Pan Tilt Brackets For Camera / Sensors for Servo SG90 MG90
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Rs. 250.00 Rs. 150.00
Add to wishlist
MG995 Tower Pro Metal Gear Servo Motor (360 Degree Rotation)
MG995 Standard Mini Micro Servo Gear Compliant with most standard receiver connector: Futaba, Hitec, Sanwa, GWS. Stable and Shock Proof Connector Wire Length 300mm Power Supply: Through External Adapter--Operating Speed: . 0.17sec or 60 degrees (4.8V no load) . 0.13sec...
Rs. 399.00 Rs. 320.00
Add to wishlist
DRV8825 Stepper Motor Driver with Aluminum Heat Shrink for 3D printer
Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer,...
Rs. 280.00
Add to wishlist
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all...
Rs. 1,050.00 Rs. 899.00
Add to wishlist
SERVO MOTOR CYS-S8218 HIGH TORQUE 40KG Motor Control
The CYS-S8218 is a well designed and high quality servo which is digital, fitted with metal gears for reliability. It is made of high quality material, which may make your operation much more remarkable. CYS-S8218 is Digital Metal Gear High...
Rs. 3,899.00 Rs. 3,149.00
Add to wishlist
MG996R (180) Tower Pro Metal Gear Servo Motor 180 Degree Rotation
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm Servo Plug: JR (Fits JR and Futaba) Servo...
Rs. 450.00 Rs. 349.00
Add to wishlist
2 Channel Motor TB6612FNG and 16 Channel (PCA9685) PWM Servo Shield for Arduino
2 connections for 5V servos connected to the high-resolution dedicated timer - no jitter!4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC.Up to 4...
Rs. 799.00
Add to wishlist
Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module
PWM capability of up to 25 kHz combined with active freewheeling. Switched mode current limitation for reduced power dissipation in overcurrent Overtemperature shut down with latch behavior. Undervoltage shut down. Overvoltage lockout.--The Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver...
Rs. 1,100.00 Rs. 949.00
Add to wishlist
ULN2003 Stepper Motor Driver Board
ULN2003A motor driver chip Chip all the pins already leads for easy connection to use 5-12V power supply 4-way signal indicator XH-5P socket can be connected directly 28BYJ-48 Model stepper motor --This is the ULN2003 Driver Module Stepper Motor Driver...
Rs. 129.00
Add to wishlist
S3003 Futaba Servo Motor-180 degree
Stall Torque (6.0V): 4.1 kg.cm, Stall Torque (4.8V): 3.2 kg.cm Operating Voltage: 4.8-6.0 Volts, Operating Speed (6.0V): 0.19sec/60 degrees at no load, Operating Speed (4.8V): 0.23sec/60 degrees at no load Control System: +Pulse Width Control 1520usec Neutral -- This is...
Rs. 450.00 Rs. 349.00
Add to wishlist
28BYJ-48 Stepper Motor DC 5V
Rs. 300.00 Rs. 149.00
28BYJ-48 Stepper Motor DC 5V
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm Note: The system is recommended to run on Half-step mode(8 step control signal sequence) for excellent performance...
Rs. 300.00 Rs. 149.00
Add to wishlist
NEMA17 Stepper Motor - 48mm
3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65"x1.65"x1.85" 4-wire Build with 1m Cable and 0.1" pitch Connector Rated current 2.0A & resistance 1.4ohms--This is an updated version nema 17 stepper motor with holding torque of...
Rs. 999.00
NEMA17 Stepper Motor - 34mm
Rs. 1,250.00 Rs. 999.00
NEMA17 Stepper Motor - 34mm
3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65"x1.65"x1.85" 4-wire Build with 1m Cable and 0.1" pitch Connector Rated current 2.0A & resistance 1.4ohms--Stepper Motor – 1.5A – 34mm is the most popular motors used to...
Rs. 1,250.00 Rs. 999.00
NEMA17 Stepper Motor - 40mm
Dimensions: 42mm x 42 mm x 34 mm (L x W x W) Movement angle: 1.8 degrees Resistance / phase: 1.5Ω Current / phase: 1.5 A Holding torque: 0.22 Nm (minimum) Inductance / phase: 2.8 Mh--NEMA17 – KS42STH34-1504A Stepper Motor...
Rs. 999.00
S3003 Futaba Servo Motor-360 degree
Stall Torque (6.0V): 4.1 kg.cm, Stall Torque (4.8V): 3.2 kg.cm Operating Voltage: 4.8-6.0 Volts, Operating Speed (6.0V): 0.19sec/60 degrees at no load, Operating Speed (4.8V): 0.23sec/60 degrees at no load Control System: +Pulse Width Control 1520usec Neutral -- This is...
Rs. 450.00 Rs. 349.00
Add to wishlist
NEMA 17 Stepper Steel and Rubber Vibration Dampers clamp
This damper is for NEMA 17 stepper motors. It can effectively reduce noise and vibration generated from the running stepper motors.
Rs. 100.00 Rs. 60.00
Add to wishlist
MG945 Digital High Speed Servo Motor
Stall torque: 10kg/cm (4.8v); 12kg/cm (6v) Operating voltage: 4.8 ~ 6.6v Temperature range: 0- 55deg Gear Type: Metal gear Dead band width: 1us servo wire length: 32cm
Rs. 399.00
Add to wishlist

Showing 1 - 24 of 33 total

You have successfully subscribed!
This email has been registered