Motors, Drivers, Actuators - Stepper Motor
Motors, Drivers, Actuators - Stepper Motor
28BYJ-48 Stepper Motor DC 12V
28BYJ-48 -12V DC Stepper Motor This 12V DC 28BYJ-48 Stepper Motor is a small, inexpensive, and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper...
Rs. 300.00
Rs. 149.00
ULN2003 Stepper Motor Driver Board
ULN2003A motor driver chip Chip all the pins already leads for easy connection to use 5-12V power supply 4-way signal indicator XH-5P socket can be connected directly 28BYJ-48 Model stepper motor This is the ULN2003 Driver Module Stepper Motor Driver...
Rs. 150.00
Rs. 99.00
28BYJ-48 DC 5V Stepper Motor Step Motor
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm Note: The system is recommended to run on Half-step mode(8 step control signal sequence) for excellent performance...
Rs. 300.00
Rs. 149.00
TB6600 Stepper Motor Driver Controller
Input Current: 0~5A Output Current: 0.5~4.0A Control Signal: 3.3~24V Power (MAX): 160W Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32 Temperature: -10～45℃ H bridge bipolar constant current drive. TB6600 Arduino Stepper Motor Driver is an easy-to-use professional stepper motor...
Rs. 880.00
Rs. 469.00
2 Channel Motor TB6612FNG and 16 Channel (PCA9685) PWM Servo Shield for Arduino
2 connections for 5V servos connected to the high-resolution dedicated timer - no jitter!4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC.Up to 4...
Rs. 799.00
DRV8825 Stepper Motor Driver with Aluminum Heat Shrink for 3D printer
Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer,...
Rs. 280.00
NEMA17 Stepper Motor - 34mm
3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65"x1.65"x1.85" 4-wire Build with 1m Cable and 0.1" pitch Connector Rated current 2.0A & resistance 1.4ohms--Stepper Motor – 1.5A – 34mm is the most popular motors used to...
Rs. 1,250.00
Rs. 999.00
Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module
PWM capability of up to 25 kHz combined with active freewheeling. Switched mode current limitation for reduced power dissipation in overcurrent Overtemperature shut down with latch behavior. Undervoltage shut down. Overvoltage lockout.--The Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver...
Rs. 1,100.00
Rs. 949.00
NEMA 17 Stepper Steel and Rubber Vibration Dampers clamp
This damper is for NEMA 17 stepper motors. It can effectively reduce noise and vibration generated from the running stepper motors.
Rs. 100.00
Rs. 60.00
NEMA17 Stepper Motor - 48mm
3D printer motor with high torque 59Ncm(83.6oz.in) holding torque NEMA 17 bipolar 1.65"x1.65"x1.85" 4-wire Build with 1m Cable and 0.1" pitch Connector Rated current 2.0A & resistance 1.4ohms--This is an updated version nema 17 stepper motor with holding torque of...
Rs. 999.00
NEMA17 Stepper Motor - 40mm
Dimensions: 42mm x 42 mm x 34 mm (L x W x W) Movement angle: 1.8 degrees Resistance / phase: 1.5Ω Current / phase: 1.5 A Holding torque: 0.22 Nm (minimum) Inductance / phase: 2.8 Mh--NEMA17 – KS42STH34-1504A Stepper Motor...
Rs. 999.00
NEMA 23 18.9 kg-cm Stepper Motor K138-PV Long Shaft
Step Angle Step Angle: 1.8 ° Current: 2.8 A/Phase Holding Torque: 189 N-cm Detent torque: 6.8 N.cm (Maximum) Lead Wires: 4 Shaft diameter: 6.35 mm--The stepper motors move in precisely repeatable steps, hence they are the motors of choice for...
Rs. 2,300.00
NEMA 23 7.2 kg-cm Dual Shaft Hybrid Stepper Motor
Step Angle Step Angle: 1.8 ° Current: 1 A/Phase Holding Torque: 72 N-cm Detent torque: 3.6 N.cm (Maximum) Lead Wires: 6 Shaft diameter: 6.35 mm (both sides)--It is a brushless DC motor, so the life of this motor is dependent...
Rs. 1,499.00
NEMA 23 10.1 kg-cm Hybrid Stepper Motor
Step Angle Step Angle: 1.8 ° Current: 2.8 A/Phase Holding Torque: 10.1 N-cm Detent torque: 3.6 N.cm (Maximum) Lead Wires: 4 Shaft diameter: 6.35 mm--They are the special choice for heavy-duty CNC machines. They overpass the NEMA17 Stepper Motors because...
Rs. 1,699.00
NEMA23 24V Stepper Motor
1.8° 76mm mini stepping motor for NEMA23 Good stability and low noise, 1.89N.m Hybrid Two phase/bipolar stepper motor Stepper motor fit for robotics, textile machinery, 3D printer etc. Size(L*W*H): 5.5x5.5x9.5 cm/2.16x2.16x3.74 inch--The stepper motors move in precisely repeatable steps, hence...
Rs. 3,999.00